- Water Decal for MG 1/100 Blue Frame 2nd Revise Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm
Tools:
* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife
Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.
Water slide decals are activated by water. So it's important to store them away from liquid.
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm
Tools:
* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife
Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.
Water slide decals are activated by water. So it's important to store them away from liquid.
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm
Tools:
* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife
Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.
Water slide decals are activated by water. So it's important to store them away from liquid.
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm
Tools:
* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife
Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.
Water slide decals are activated by water. So it's important to store them away from liquid.
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm
Tools:
* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife
Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.
Water slide decals are activated by water. So it's important to store them away from liquid.
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm
Tools:
* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife
Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.
Water slide decals are activated by water. So it's important to store them away from liquid.
- Water Decal for PG FX-550 SKY GRASPER water decal
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 21 cm x 24 cm
Tools:
* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife
Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.
Water slide decals are activated by water. So it's important to store them away from liquid.
- Water Decal for PG 1/60 MBF-02 Strike Rouge Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11.5 cm x 13.5 cm
Tools:
* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife
Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunpla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.
Water slide decals are activated by water. So it's important to store them away from liquid.
- Water Decal for RG 1/144 FX550 SKY GRASPER water decal
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm
Tools:
* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife
Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.
Water slide decals are activated by water. So it's important to store them away from liquid.
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 10 cm x 9 cm
Tools:
* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife
Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.
Water slide decals are activated by water. So it's important to store them away from liquid.
- Water Decal for Water Decal MG 1/144 Gundam Seed Blitz Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm
Tools:
* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife
Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.
Water slide decals are activated by water. So it's important to store them away from liquid.
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm
Tools:
* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife
Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.
Water slide decals are activated by water. So it's important to store them away from liquid.
- Water Decal for MG 1/100 RX-178 MK-II MK2 AEUG Gundam Water Decal
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 15 cm x 20 cm
Tools:
* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife
Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.
Water slide decals are activated by water. So it's important to store them away from liquid.
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm
Tools:
* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife
Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.
Water slide decals are activated by water. So it's important to store them away from liquid.
This is a sheet of water-slide decals, dry transfers, or self-adhesive stickers for use in detailing anime or science-fiction kits.
This set of decals was made especially for Bandai's 1/100 HG YF-29 Durandal Valkyrie (Maximilian Genus Custom) Full Set Pack model kit! Decals are included for all three forms: Battroid, Gerwalk and Fighter. Order yours today!